1969 Mercury Cougar

New old stock ashtray for any 1969-70 Mercury Cougar or Ford Mustang with factory console. This is the rear ash tray. Ford part number C8AZ-6262876-A.

Used rear console support bracket for the 69 Cougar or Mustang. Mounts under the leading edge of the storage compartment under the console.NOTE - 69 and 70 used different brackets

For deck / trunk lids it is all about rust under the inner rear lip... We still check it over good for excessive filler, correct contour on all the lines and hidden rust under the weather strip. We ship deck / trunk lids with several layers of thick cardboard and insure them for the full amount. Keep in mind shipping is free if you order at the same time as a hood, door or quarter panel. For those wanting a cleaner look on their 1967-68 Cougar a 69-70 deck / trunk lid will bolt right on with...

Used décor rear interior panel in aqua for the driver side (left hand) of the Mercury Cougar coupe. The décor interior is one level above the base standard interior. Interior code for base standard interiors starts with 1, décor interior codes can start with 3, 5, or E, followed by another letter denoting color. *NOTE* Armrests sold separately. Specify if your Cat requires power window cutouts in the comments section.

Used décor rear interior panel in dark red for the driver side (left hand) of the Mercury Cougar coupe. The décor interior is one level above the base standard interior. Interior code for base standard interiors starts with 1, décor interior codes can start with 3, 5, or E, followed by another letter denoting color. *NOTE* Armrests sold separately. Specify if your Cat requires power window cutouts in the comments section.

Used décor rear interior panel in dark red for the passenger side (right hand) of the Mercury Cougar coupe. The décor interior is one level above the base standard interior. Interior code for base standard interiors starts with 1, décor interior codes can start with 3, 5, or E, followed by another letter denoting color. *NOTE* Armrests sold separately. Specify if your Cat requires power window cutouts in the comments section.

Used XR7 rear interior panel in dark red for the driver side (left hand) of the Mercury Cougar XR7 coupe. This was the top of the line interior trim package and could only be had with an XR7 model. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. *NOTE* Arm rests sold separately. Specify if your Cat requires power window cutouts in the comments section.

Good used Grade "A" rust free valance. Getting to be hard to find without excessive filler or severe damage. We have a local body man take small dents out and he does not load them up with Bondo. He removes the filler and works the dent out properly. These are not paint ready, flawless parts but rather 40 years old, taken from a parts car. We do have NOS and on occasion we we get in a flawless used example. We have no plans to start selling the fiberglass reproductions as we feel good used,...

Good used Grade "B" valance. These valances may have some surface rust and a few dings or dents. You will definitely have to do work on these to get them ready for paint. We now sell a very high quality reproduction that is made of thicker material than OEM. Ford part # C9WY-6540544-A.

This is a grade 'A' used mirror assembly with no UV damage and has had the mirror lens "re-silvered". Keep in mind a restored lens that is decades old will look good when finished but almost never flawless as the surface of the glass will usually have light scratches and often faint spotting on the backside from previous water damage / staining. Sold outright, no core required. NOTE: Pictured is black, but if you would like a specific color other than black please mention it in the...

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored 1967 early style larger rectangular rear view mirror lens for the Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or...

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored rear view mirror lens for the 68 - 73 Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or discoloration in the lens. If your...

Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Look for the SUN-X logo to determine if your glass is tinted or not. For those wanting Grade "A" glass, we recommend calling us so we can discuss with you the glass that we have available.Need a little help identifying some of the markings on your...

Professional strength adhesive for attaching your rearview mirror bracket to your windshield. Good for 1968 - 1973 Cougars and Mustangs. 1967's Didn't have the bracket attached to the windshield.

Basic FMX transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. Quality kit, same as supplied to professional shops. 

1969 Ford four speed shifter rebuild kit. Kit includes tension spring, steel clip, threaded machined shaft, pair of roll pins, pair of dowel pins, and two bolts. Information indicates that all 1969 4 speed shifters are the same across all car lines and for all engines. Link to the Ford shifter linkage expert. Check out our video on rebuilding your shifter below: ...

Core regulator assembly or brain box for factory speed control on a early 1968-69 Mercury Cougar or Ford Mustang. This is the Perfect Circle regulator assembly. Basic Ford part number is 9D757, research has not turned up the complete Ford number possibly C8VY-9D757-A. Core grade, most likely will need servicing or repair. Bare unit, no brackets, wiring or cables. *Note - We do not have the tools or know how to test this unit. 

Low fuel option electrical relay. Stamped C6AF-10A968-A, Ford engineering number C5AZ-10A968-C. This relay was used on 1965-70 Ford and Mercury full sized cars, 1968-70 Torino/Cyclone/Montego/Fairlane, along with 1967-70 Mercury Cougar and Ford Mustang with that low fuel option. New Old Stock relay. *Note - Generally this will not solve your low fuel indicator problems. The low fuel indicator failure is almost always due to a failed thermistor. The thermistor is located on the fuel sending...

NOS seat belt warning light relay for most Ford Lincoln and Mercury cars starting in 1967 until sometime in 1972 when a Motorcraft version of this exact relay was produced. This is a timed relay that allows several seconds of illumination to your seat belt warning light. Ford Part number C7AB-10B924-B1, Ford Service part number D1AZ-10B924-A or D2AB-10B924-AA.

These are all new, not rebuilt, OEM Ford quality. We recommend these over the generic version and the "concours" version. Marked with Ford D2AF-11450-AA part number, but is functionally correct for all 1967-73 Cougars. Black case as original.Replaces Ford Part #: C7AF-11450-A1 , B6AZ-11450-A , C7AZ-11450-A , D2AF-11450-A , etc

New old stock tilt / tilt away steering column lock relay for the Mercury Cougar or Ford Mustang. Keep in mind we have a reproduction substitution for this part. This unit can be identified with the bend in the bracket compared to the 1967 relay which is straight.  Ford part # C8ZA-3E553-A. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.co...

This three part clip was used on all four versions of the 1969 - 1970 remote mirror to keep the door glass from interfering with the cable.

New old stock Ford accessory cable trunk popper. Fits late 1967 - 1973 Mercury Cougar and other Ford products. Lever release, complete kit, NOS Ford. Detailed instructions included.  Ford part number C7AZ-62432A00-A. *Note - All 1967, and most 1968 trunk lids will not have a large enough access opening in the under side structure to allow the trunk latch to be inserted. 

New old stock Ford accessory electric trunk popper. Fits late 1968 - 1973 Mercury Cougar and other Ford products. Electric push button release, complete kit, NOS Ford. Detailed instructions included.  Ford part number C9AZ-54432A00-A. *Note - All 1967, and most 1968 trunk lids will not have a large enough access opening in the under side structure to allow the trunk latch to be inserted. 

Ford OEM kit for rebuilding your power steering control valve on any 1962-70 Ford or Mercury. All parts in photo are included. We also have the complete rebuild kit available.  NOS power steering control valve repair kit.  Ford part number C2AZ-3A553-A.

Good used metal strip that fastens the weatherstrip to the bottom side of the header bow. Keep in mind we have (almost) every single used part related to the 69-73 Convertible Cougar and convertible Ford Mustang / Shelby in stock at all times.

Used rear leaf spring retainer for 1967 -73 Mercury Cougar with competition handling or GT suspensions. Additionally it fits 1966-71 Mercury Comet / Montego / Cycolne, 1966-71 Ford Fairlane / Torino, all with HD or GT suspensions. Identified with a stamped number "2" on the top. The inside height is 1-29/32 or 1.91 inches. Sold individually, one for each side for a total of 2 per car. Bead blasted for pictures, most will ship 'as removed'. This suspension part never came painted, there will be...

Nice reproduction clip for attaching the speedometer cable onto 3 and 4 speed 1967-70 Mercury Cougar and Ford Mustangs. Mounts to the firewall.

Larger sized retainer that screws to upper front lip near the quarter glass on all 1969-70 Mercury Cougar hardtops and 1970 Ford Mustang coupes. Ford lists this part as: Retainer - quarter trim panel rear. We see these sometimes installed in the front position at the top of the interior quarter panel next to the window glass, mostly the front position is empty or the factory installed two of the smaller retainers. This retainer helps the top section of the soft trim panels from rattling. The...

This clip secures the clutch pedal rod end as it comes through the clutch pedal hanger.C8AZ-2B277-A

NOS retainer / friction clips that replace broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper piece of this shaft...

Good grade "A" used nut with minimal scratches from removal process. The originals have deeper grooves and have a better luster on the chrome than the reproductions. This is a one year only design. Don't forget to check out our special tool used to remove and install this nut.

This fits behind the door panel and is needed to install your remote mirror correctly.*NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

If your original is pitted or has come apart this will be a clean, crack free used replacement that will easily snap in place. We have a reproduction, but the finish is rougher, as shown in the comparison photo. There were originally two versions of this switch: the one shown with both round contact points in plastic, and another which had one in metal.

Used Rod for the bell crank accelerator for 1969 Mercury Cougar and Ford Mustang with speed control. The Rod fits between the Servo and Bell Crank. Ford number may be C9ZZ-9D774-A, just a guess.Ford part number 9D774.

This rod was used on the Bendix brand booster (crimped together case). It measures 5 3/4" long. Used on many Ford products including Torino, Cyclone, Ranchero, Cobra, Fairlane and others. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot...

This is a modern upgrade to your manual transmission cars. It replaces the bushing that is in the crank shaft. Supports the tip of the input shaft of the transmission. Quality part with roller bearings on the inside, fits small block only.Replaces Ford Part #: C7AZ-7600-A.

New RTV  oil resistant, high temperature, Ultra Black gasket maker for use on the Mercury or Ford. It's no mistake that Ultra Black has become an automotive industry standard. It's low odor, flexible, non-corrosive, vibration resistant, oil resistant, heat resistant, fast curing formula cannot be beat. Great for use on any surface that experiences high heat and oil like the valve cover gaskets.

New Permatex RTV gasket dissolver, good for all makes, models, and years. Use this stuff when you want to remove any remnants of those old worn out silicone gaskets made with any of the common gasket makers. Handy item to have on hand so you dont have to keep using your putty knife or screwdriver! 

The 69-73 looks the same as the earlier version once installed but the casting number will read C3AA-4906-C on the early unit and C9OA-4906-A on the 1969-73 version. We have found a few rubber bumpers marked D3Z... very few. See other listing for that one..

Companion reproduction insulation for our premium 1969-70 Mercury Cougar sail panels. These were created by a Cougar enthusiast for Cougar enthusiasts. Copied from an original 1969 Cougar Eliminator. Sold in pairs, originally held up with a bit of spray adhesive glue. Same thickness heavy felt as originals.

Reproduction black rear interior sail panels for 1969 Mercury Cougar standard models without courtesy light provision. Reproduction rear interior sail panels made from foam core backer board, covered in textured black vinyl with embossed border. Original panels were made of textured paper. We recommend white for color changes, it is also recommended that you use a quality vinyl paint. Sold in pairs, 1969 standard in black. Will also work on 1970. See related items for reproduction insulation....

Reproduction white rear interior sail panels for 1969 Mercury Cougar standard models without courtesy light provision. Reproduction rear interior sail panels made from foam core backer board, covered in textured white vinyl with embossed border. Original panels were made of textured paper. We recommend white for color changes, it is also recommended that you use a quality vinyl paint. Sold in pairs, 1969 standard in white. Will also work on 1970. See related items for reproduction insulation. ...

Reproduction rear interior sail panels for 1969 Mercury Cougar XR7 and standard models with courtesy light provision. Reproduction rear interior sail panels made from foam core backer board, covered in textured black vinyl with embossed border. Original panels were made of textured paper. Metal reinforcing ring installed for courtesy lights. Several different versions of courtesy lights were used 1969-70. These allow the installation of the chromed reproduction courtesy lights which look great...

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

Sold individually, original glove box cable screw with shoulder. For any 1967-70 Mercury Cougar or Ford Mustang. Probably many other Ford and Mercury cars also.Ford part number 379202-S2.