Other Mouldings

These are 100% correct reproductions for the 1968 Mercury Cougar XR7-G, but will fit any 1967-68 Cougar. These will NOT lay flat against the valance, as the originals did not. These are beveled on purpose and if you attempt to straighten them they WILL break. The reproductions that do lay flat against the valance are no longer being produced. We cannot warranty these against any attempts to straighten them. Sold as a pair. ...

THIS KIT HAS A CORE CHARGE OF $950 Here is a time and money saving package deal for the person restoring their 1967 or 1968 Cougar. This package includes: Hood lip moulding Fender extension mouldings Quarter extension mouldings Grille center trim Deck lid moulding Drip rail mouldings Nine piece front and rear window trim Front and rear Award Winning Bumpers All parts are show quality. The bumpers are triple plated chrome, the aluminum has the correct anodized finish just like NOS and the...

Used 1968 Mercury Cougar GT-E horizontal grille bar clip or keeper for the center grille section. This is a rare find, limited to stock on hand.

Reproduction clip for the rear quarter extension moulding / trim on the Mercury Cougar. The rear quarter extension moulding / trim uses 2 different size clips. This is the smaller of the two. One per side, 2 per car. Get the larger clip here. Replaces Ford part # C7WB-65291B80-A. *NOTE* Will work with the 1967-70 trunk trim, but the nuts are wrong style.

Reproduction metal rear deck / trunk lid moulding / trim clip for the Mercury Cougar. This clip comes with a correct looking nut and works with the 1967-68 aluminum trim and the 1969-70 stainless steel trim. This unit measures about 1-7/8" long with a stud height of about 3/4". 7 clips needed per trunk lid. Note that this clip features a stud that is a little longer than what was factory. If you have a swollen lip (rust) on your deck this will be an advantage to you, if not you will have to...

Used rocker moulding end clip. Fits all 1968 Mercury Cougars. This clip is plastic and metal, it has a stud which goes through the body of the car. sold individually, 4 total needed per car. Our all metal version of this clip is reproduced and is a better value. Find it here.Ford part number C7OZ-6221094-A.

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. This particular clip is used on many Ford cars throughout the 60's and 70's. This listing is for a box of 100 clips. We recommend buying...

Set includes ten rectangular clips with pop rivets and two incorrect, irregular shaped end clips (Mustang Part). These clips will fit the 68 Cougar, but are actually replicas of the clips for the 67-68 Mustang. Rather than the plastic end clips in this kit, we recommend the metal version that we sell separately. NOTE - We've found that these reproduction clips do not work as well as the originals, you may find it a bit hard to install the rockers onto these clips without having to...

Used driver side (left hand) factory stainless steel door guard for the Mercury Cougar.NOTE: This item will not ship until a useable core is received.

Used passenger side (right hand) factory stainless steel door guard for the Mercury Cougar.NOTE: This item will not ship until a useable core is received.

NOS, new old stock, Stainless steel clip on guards for the rear edge of the 1967 and 1968 Cougar doors. Would have been part of the exterior decore option. Self attaching, no adhesive or screws needed. Specifically contoured to the Cougar door edge. Ford part number C7WY-6220910-A.

Stainless steel clip on guards for the rear edge of the 1967 and 1968 Cougar doors. Would have been part of the exterior deccor option. Self attaching, no adhesive or screws needed. Specifically contoured to the Cougar door edge. These used trim parts will have many very small dings and scratches. The driver side moulding will have substantially more damage than the passenger side moulding. Ford part number C7WY-6220910-A. NOTE: This item will not ship until useable cores are received. ...

The 1967 XR7 did not have rocker panel mouldings as did the 1968 - 1973 XR7 Cougars. All 1967 XR7 models came equipped with these "Hash" marks fastened to the rear of both rockers, at a rear tilting angle. Both sides received seven ribs, held by two Phillips screws each for a total of fourteen ribs in all. They were painted semi-gloss black in the recessed areas and the screws themselves were black as well. The leading ribs are usually pretty rough looking due to road debris wear, the one...

Flat nut for attaching the "Mercury" script on the front fender extension on all 1967-68 Mercury Cougars. 4 total needed for emblem installation on that fender extension. Also attaches the reproduction running cat emblem to the headlight door on 1967-69 Mercury Cougars.

This reproduction tape is a must for anyone replacing their stainless steel window trim pieces on the 1967 - 1968 Cougar or Mustang. Can be used on any of the side windows. We suggest saving the original quarter window rubber surround if possible, due to the curves, but this tape can be used there as well if needed. This glass setting tape is designed to look and perform similarly to the original Ford factory material. It creates a water tight bond as well as...

Used 1968 Mercury Cougar GT-E horizontal grille bar, from the driver side headlight door. Measures 15-3/16 inches long. This is the longest section of extruded aluminum from an original car. There are a total of 7 pieces for a complete grille on a GT-E. It can be cut down to fit any other position that you may be missing. This is a rare find. This one has road tested, meaning that it does have some minor scuffs from use.

These are very correct looking reproductions and sold as a complete set. They do not come with the keepers that go on the backside of the grill, so you will be using common flat washers which actually work just fine. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

Complete set of seven, extruded aluminum original horizontal GTE grille bar set. Includes all parts in good condition including the four rectangular, notched brackets that attach the center bars from the back side. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

This listing is for all six pieces restored and of course requires you send your cores in advance. It can take anywhere from 1 to 4 months depending on what time of year it is and where we are in our cycle with our plater as we send a minimum of $20k in at a time. We make sure they are separated from the more common parts we have and these are treated with special care every step of the way. On this particular set we never ask them to hurry. Do know that if you have extra holes drilled they...

This pair of tail light bezels have been chemically dipped to remove the chrome and are ready to be painted black for your 1967 - 1968 Resto-Mod or 1968 GTE. Keep in mind when an item is chromed, the layer or layers of copper plating act as a primer to fill in minor imperfections. You will have some prep time involved before these are paint ready. We hand select premium parts that have minimal defects.  If you send cores in for exchange they must be pit free and no scrapes so as to...

1968 Mercury Cougar left side or driver door moulding found on the GT-E models. This unique trim split the lower silver color from the body color. Arrow straight, dull, a couple of minor, very small scratches. We won't always have this stick of trim in stock, but we will work to accurately describe the exact piece that we do have in inventory. We will take used GT-E trim in trade towards the reproduction GT-E trim call 503-463-1130 for details.Ford part # C8WY-6520939-A.Due to the difficulty...

1968 Mercury Cougar right side or passenger door moulding found on the GT-E models. This unique trim split the lower silver color from the body color. We won't always have this stick of trim in stock, but we will work to accurately describe the exact piece that we do have in inventory. The trim pictured is dull, but has no dents or scrapes. Laser straight with only minor scratches and pock marks from road debris on the lower side closest to the fender. We will take used GT-E trim in trade...

This restored drip rail moulding / trim will have had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. Our mouldings / trim are sold outright, as a pair, or one side only. Most people will be satisfied with our used grade "A" drip rail mouldings / trim, however these are for the person that is striving for perfection with his or her show car. Ford part # driver side...

This passenger side (right hand) restored drip rail mouldings / trim will have had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. Our mouldings / trim are sold outright, as a pair, or one side only. Most people will be satisfied with our used grade "A" drip rail mouldings / trim, however these are for the person that is striving for perfection with his or her show...

1968 Mercury Cougar right or passenger side fender moulding found on the GT-E models. This unique trim splits the lower silver color from the body color. The unit shown is the one you will receive. Near mint, excellent original bright dip finish, an out of package (we still have remnants of the crispy brown FoMoCo wrapper) NOS part with minimal shelf wear. Best you will ever find, ready to put on the car as is. We won't always have this stick of trim in stock, but we will work to accurately...

1968 Mercury Cougar right or passenger side fender moulding found on the GT-E models. This unique trim split the lower silver color from the body color. This core piece good is for restoration. We won't always have this stick of trim in stock, but we will work to accurately describe the exact piece that we do have in inventory. We will take used GT-E trim in trade towards the reproduction GT-E trim call 503-463-1130 for details.Ford part # C8WY-6516039-A.Due to the difficulty in obtaining trim...

1968 Mercury Cougar left side or driver rear quarter moulding found on the GT-E models. This unique trim split the lower silver color from the body color. Good used core with a few minimal dings on the raised portion and will easily restore to mint condition. We won't always have this stick of trim in stock, but we will work to accurately describe the exact piece that we do have in inventory. We will take used GT-E trim in trade towards the reproduction GT-E trim call 503-463-1130 for...

Mounts horizontally at the base of your quarter window. This used part will show age on the chrome but will not be pitted. If you are wanting to match the patina of a low mileage unrestored car this part will save you money over our repro unit. Original Mercury part number is C7WY-6529035-A with a casting number of C7WB-6529035-D

Restored quarter window to drip rail moulding / trim for the driver side (left hand) of the Mercury Cougar. This stainless trim part affixes to the "C" pillar and fills the gap between the roof side weather strip and drip rail gutter. Also known as "Roof Side Cover Retainer."

Stainless trim part that affixes to the "C" pillar. This trim part fills the gap between the roof side weather strip and drip rail gutter. Also known as "Roof Side Cover Retainer"

Used quarter window to drip rail moulding / trim for the driver side (left hand) of the Mercury Cougar. This stainless trim part affixes to the "C" pillar and fills the gap between the roof side weather strip and drip rail gutter. Also known as "Roof Side Cover Retainer."

This obscure little part fills the gap on the underside of the roof rail where the rear 1/4 window meets the "C" pillar. Also known as "Roof Side Cover Retainer"

This obscure little part fills the gap on the underside of the roof rail where the rear 1/4 window meets the "C" pillar. Also known as "Roof Side Cover Retainer"

Unlike our reproduction rocker mouldings, we can sell these used mouldings individually (shipping is the same price when you buy one or several). Even though there is no difference in fit or part number, we do ask that you choose passenger side or drivers side by mentioning it in the notes as the finish is always duller on the front end, behind the front tires from road debris. The majority of our used 1968 rocker moldings have one screw hole towards the front. Reason being is that there were...

Used driver side upper quarter window channel for all 1967-68 Mercury Cougars. This is the stainless steel upper glass frame section only. Our used trim will have some fine scratches or scuffing present. Driver side only, passenger side also available. Restored also available. Replaces Ford part number C7WY-6529963-A.Check out our video below for helpful tips on disassembling your vent and quarter windows: ...

Used passenger side upper quarter window channel for all 1967-68 Mercury Cougars. This is the stainless steel upper glass frame section only. Our used trim will have some fine scratches or scuffing present. Passenger side only, driver side also available. Restored also avialable. Replaces Ford part number C7WY-6529962-A.Check out our video below for helpful tips on disassembling your vent and quarter windows: ...

Restored trim piece for 67 - 68 Cougars. This is the trim that goes around your driver side quarter window. And since it has been restored, it will be polished to a much higher luster than what the factory would have done.Check out our video below for helpful tips on disassembling your vent and quarter windows: ...

Restored trim piece for 67 - 68 Cougars. This is the trim that goes around your passenger side quarter window. And since it has been restored, it will be polished to a much higher luster than what the factory would have done.Check out our video below for helpful tips on disassembling your vent and quarter windows: ...

This pair of restored drip rail mouldings / trim will have had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. Our mouldings / trim are sold outright, as a pair, or one side only. Most people will be satisfied with our used grade "A" drip rail mouldings / trim, however these are for the person that is striving for perfection with his or her show car. Ford part #...

This is the right hand and left hand 1/4 panel moulding. Some refer to these as "Hockey Sticks" or "J" mouldings. They mount at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled in them to fasten these in place. Included with the moulding is super strength 3M double sided, trim tape. Original Mercury part number was C7WY-6529034-A & C7WY-6529035-A.We have found that this 3M product works great for bonding these parts...

This is the left hand or "Driver Side" 1/4 panel moulding. Some refer to this as a "Hockey Stick" or "J" moulding. It mounts at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled in them to fasten these in place. Included with the moulding is super strength 3M double sided, trim tape. Original Mercury part number was C7WY-6529035-A. We have found that this 3M product works great for bonding these parts in place...

This is the right hand or "Passenger Side" 1/4 panel moulding. Some refer to this as a "Hockey Stick" or "J" moulding. It mounts at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled in them to fasten these in place. Included with the moulding is super strength 3M double sided, trim tape. Original Mercury part number was C7WY-6551728-A.We have found that this 3M product works great for bonding these parts in place permanently....

Inner rectangular clip to hold on the rocker panel moulding on a 1967 or 1968 Ford Mustang or Mercury Cougar. Sold Individually.NOTE - We've found that these reproduction clips do not work as well as the originals, you may find it a bit hard to install the rockers onto these clips without having to apply too much pressure, causing unwanted bending.

Used plastic rocker moulding clip for 1968 Mercury Cougar and 1967-68 Ford Mustang. Used clip, originally pop riveted onto the rockers. Sold individually. Ford part number C7ZB-6510182-A.

This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. You will notice the reproduction has a larger head (The two on the right in the lower picture are repros) than both of the used versions typically found on 67-73 Cougars. This will be a benefit to those that have elongated screw holes on your wheel lip mouldings from corrosion or improper removal. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding,...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD individually. See related items for kit of 10 screws. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD AS A SET OF 10.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972...

Not 100% correct, but close and functional. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. Sold as a box of 100.