Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Used rubber bumper for the tilt column. 70 - 73 tilt columns require 3 bumpers, one on the lower and two on the upper knuckles. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers...
Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 8-32 thread. Ford part # D0AZ-3D739-A. *NOTE* For tilt column service, you can...
This item holds the release bale to the upper knuckle. It is different than the 67 - 69 clip although both can be used. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...
This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar...
Tilt release lever or bale. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Used lock insert for the steering column in the Mercury Cougar or Ford Mustang equipped with the tilt steering column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column...
This linkage fits between the gear at the bottom of the key lock and rod that goes to the ignition switch on the tilt column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...
This extension holds the inner spring tube in place on the 70 - 73 tilt column. Fragile piece, should take great care when tapping on this pot metal piece. Limited supply. Ford casting number: D0ZA-3790-*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony...
Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE*...
Reproduction locking pawl for the 1970 - 1979 Mercury Cougar or Ford Mustang that is equipped with a factory tilt steering column. This unit works in conjunction with a pin and is responsible for locking the tilt column in place. In many cases, the pin tends to move out of place and break or...
Used steering column tube retainer for the Mercury Cougar or Ford Mustang equipped with the tilt steering column. These little units help hold the steering column together and there are 3 required per column. Sold individually. Ford part # C8SZ-3499-A. *NOTE* For tilt column service, you can...
Locking pawl catch pin and locking pawl pin for your 70-73 Lincoln - Mercury - Ford tilt steering columns. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to you locking pawl. These shafts are notorious for working their way out of place with normal use. Once...
Locking pawl pin for your 70 - 79 tilt steering column for all Lincoln - Mercury - Ford products. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to your locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin...
1971 working, used ignition switch. This is only the electrical side, the mechanical key and lock section is not included. See appropriate shop manual for proper alignment and installation. Tested and working ignition switch. Follow the instruction in your shop manual for installation and...
Steering column to steering box coupler, also known as a 'rag' joint. Used on 1971 1972 1973 Cougar tilt columns. Good used condition, supplied with one, 12 point attaching bolt. You will need to reuse one of your factory ones. Splined end slightly larger than previous years, due to the upgraded...
Tilt steering column cover plate for turn signal lever. Two versions, two different sizes of openings for the turn signal wand. Original used Ford part, plan on painting to match your steering column. Fits all 1970-71 Mercury Cougar, 1970 Ford Mustang, and other Ford/Mercury cars with factory tilt...
Good used upper collar for the tilt column on the 1971, 1972 and 1973 Mercury Cougar or Ford Mustang.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist...
Used in all of 1970 and the early part of 1971. This collar uses the 'small' access plate cover. Ford master part number D0AZ-3D505-A, casting number on the part is D0AA-3D505. Nice condition, no cracks or damage. Also fits 1970-71 Lincoln MKIII and Thunderbird.*NOTE* For tilt column service, you...
Spring used to apply tension to the tilt locking pawl. 1967 thru 1969 required two springs due to the tilt away function. 1970 and later required only one spring.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...
Spring that fits into the steering column collar. Two springs in total that hold your key lock cylinder in place. Two required per car.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...
Ignition cylinder for the cars manufactured after 5/17/1973. Ignition lock set is new original from the O.E.M. source. Factory fresh with two keys. Fits many ford makes and models manufactured in 73 - 76. Replaces Ford Part #: D4AZ-11582-A.
1972 working, used ignition switch. This is only the electrical side, the mechanical key and lock section is not included. See appropriate shop manual for proper alignment and installation. Tested and working ignition switch. Follow the instruction in your shop manual for installation and...
1973 working, used ignition switch. 1973 version has a longer pigtail, and has a shield or tube covering the wires. This is only the electrical side, the mechanical key and lock section is not included. See appropriate shop manual for proper alignment and installation. Tested and working ignition...
Ford part number 3E629. Molded rubber construction, fixed and tilt steering columns. These may have been used as early as late 1972, not sure. Limited stock. The reproduction plastic version for 1969-72 will also fit and work in conjunction with the available foam insulation. *NOTE* For tilt...
Used locking pawl for the 1970 - 1979 Mercury Cougar or Ford Mustang that is equipped with a factory tilt steering column. This unit works in conjunction with a pin and is responsible for locking the tilt column in place. In many cases, the pin tends to move out of place and break or chip the...
Used lower steering column knuckle for the Mercury Cougar or Ford Mustang. This unit is used in the 1970-73 tilt only column and can be the issue when you have a sloppy feeling tilt column. The hard steel pin will often waller out the soft cast metal and cause play in the column. Ford part #...
Used upper steering column knuckle for the Mercury Cougar or Ford Mustang. This unit is used in the 1970-73 tilt only column. Ford casting # D1AZ-3511-AWA.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent...
Used lock insert for the steering column in the Mercury Cougar or Ford Mustang equipped with the fixed steering column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...
This linkage fits between the gear at the bottom of the key lock and rod that goes to the ignition switch on the fixed column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since...
Reproduction ignition switch. This is only the electrical side, the mechanical key and lock section is not included. See appropriate shop manual for proper alignment and installation. Follow the instruction in your shop manual for installation and adjustment. Original Ford part number...
This clip clamps together the two edges of the shroud and sets into the mounting holes on the column. It is very hard to remove, and often the tab will break off very easily.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of...
This retainer clamps together the two edges of the shroud and sets into the mounting holes on the column. The original is very hard to remove because of the saw blade teeth inside the grooves, and most times the tabs will easily break off. This reproduction will not have those...
Reproduction ignition switch for the 1973 Cougar. This version has a longer pigtail, and has a shield or tube covering the wires. This is only the electrical side, the mechanical key and lock section is not included. See appropriate shop manual for proper alignment and...
Used plunger spring used in the bale of the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Small plunger spring for 1967-69 tilt columns. Maintains pressure on the heavy wire tilt release bale. This icon means that we're looking to buy this part!WCCC is a buyer of...
Steering column locking gear. For all 1970-73 Ford and Mercury steering columns. Made of brass, has 8 teeth and is 7/16 inches thick. Fits fixed and tilt steering columns. Ford part number D0AZ-3E717-A.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony...
Used return spring for any 1970 - 1978 Cougar or Mustang Tilt Column. This spring provides return tension on tilt steering wheels.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...
Used tube insulator for the lower portion of the steering column found in 1969-72 Mercury Cougar or Ford Mustang. Because of the very fragile nature of this unit, stock is limited. Reproduction version is normally available, see related items. Ford part # C9AZ-3E629-A. *NOTE* For tilt column...
Shrink-on plastic sleeve that is found on the lower part of the collapsible steering columns. Used sleeves are often ripped and torn. Simply cut off your old sleeve and install this item to give your column a newer look and feel. Installation: Make sure that your column is clean. Lube the column...
This is the electrical portion of the new for 1970, locking column mounted switch. This is the rod actuated device mounted on the top of your column under the plastic collar cover. See page 33-02-06 of your 1970 shop manual for proper installation and adjustment. Working, used ignition switch....
Good used actuating rod for the ignition switch on the 1971, 1972 and 1973 Mercury Cougar or Ford Mustang. 8-1/8 inches on rod center long.
Used tumbler linkage arm that connects to the to ignition switch on your 1970 Cougar or Mustang equipped with a tilt column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...
Used centering ring for any fixed or tilt column on a 1969 - 1973 Cougar or Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
This is a plastic cushion, washer and/or spring between the lower knuckle and inner tube on a 1968 - 1973 tilt-away steering column. These have a larger diameter than the 1967 plastic cushion.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a...
Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single...
Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 6-32 thread. Ford part # C7SZ-3D739-A. *NOTE* For tilt column service, you can...
Used upper steering column bearing for your 67 - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. The used lower bearing can be found here. Outside diameter: 1 3/16 " * - may not fit some 67 Mustang applications...
Used lower steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. The upper bearing can be found here. Outside diameter: 1.500"Inside diameter: 1.060" *NOTE* For tilt column service, you can contact...
12 Point bolt for attaching the steering column coupler to the steering box. All 1967-73 Mercury Cougar and most all other Ford, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns.*NOTE* For tilt column service, you can contact Tony Augustine at...
1969-1973 20 amp Buss style glass tube fuses sold in a package of 5 and used in multiple positions. They are used for accessory feed, seat belt warning, tilt swing column, speed control, door ajar, low fuel, and power window relay.
Reproduction of the upper steering column bearing for your 67* - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. You can find the lower bearing here. Outside diameter: 1 3/16 " Inside diameter: 15/16 "Thickness:...
Reproduction steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. Outside diameter: 1 1/2" Inside diameter: 1 1/4"*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.co...
Reproduction pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and 2 - 4 are required per car. Pin is custom made on short runs and is very difficult to find. .001 undersized, and with 8/32 threads instead of...
Used snap ring that is used to hold the bearing on you the steering shaft. This ring was used on 67 - 78 fixed columns and 70 - 78 tilt columns. Not for use on 67 - 69 tilt columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague...
Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at...
Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column...
NOS retainer / friction clips that replace broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known...
1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used pin for the locking lever in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Two are required in 1967-69, but only one is required for 1970 and...