Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually. These clips attach to posts built in to the car. In case you're missing some...
Tubular or barrel nut for attaching our reproduction "C" pillar XR7 emblems with studs. We found these fasteners to install the emblems without disturbing the headliner of a 1967-68 Mercury Cougar. These are also suitable for installing this emblem onto the trunk lids of 1971-73 Mercury Cougar XR7 models. The originals were flat backed and glued onto the deck lids with adhesive. These tubular nuts require two 7/32" holes be drilled. These mount on the lower part of the roof behind the...
Bolt for installing the front inner and outer bumper brackets to frame rail, and rear bumper brackets to body inside of trunk. Sold individually, 8 per car.
Reproduction bolts for the deck/trunk lid latch for the Mercury Cougar or Ford Mustang. This is a set of five bolts and will fit both the standard and XR7. Total of 5 bolts used 1969-73, 1967-68 Cougars will only use 2. We think that Mustangs use 5 on all years 1967-73.AMK F-227 ...
Fits all models.
The majority of the rocker moulding end clips we get look like this unit in that the stud is broken or the wire tensioner has been broken off. Putting a new stud in one of these clips is not a hard job. Sold Individually.
Ten of these plastic clips are required per car, five on each side. Original clips with D1ZB-6510182-AA engineering number imprinted on them. Sold Individually.
These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. This particular clip is used on many Ford cars throughout the 60's and 70's. This listing is for a box of 100 clips. We recommend buying...
Self threading white plastic. Used on front and rear valances.Sold individually.
Reproduction keeper clip that attaches to the secondary articulating stabilizer arm and slides into place to secure the pin that holds the arm.
Exact replacement inside door handle nut, trunk lock nut, and hood scoop nut. Same finish as originals. 10 of these are used to mount the 68-71 hood scoop found on the 68 428 CJ, 69-70 Eliminator, 69-70 428 Ram Air equipped Cougars and 71 GT and 429CJ. Two of these per door are used on the 69-70 inside door release. Two of of these nuts used to attach 1967-68 Cougar trunk locks.
Complete engine mounting kit for the 390 engine with standard exhaust. See list below for included hardware.Click on images to enlarge. ...
Reproduction exterior convertible boot moulding / trim nuts for the Mercury Cougar or Ford Mustang and Torino. Here's another great reproduction brought to you by WCCC! Each vehicle will require 20 nuts. Sold individually.
This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. These are sold individually.Replaces Ford part # 373556-S. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...
Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved. Sold in a box of 100, we also list them individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71...
Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved. Sold Individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71 - 73 = 16 front, 18 rear Here's a handy...
These vinyl coated clips hold the weatherstrip and guide the window when rolling up. Used clips usually are rusted and the vinyl portion is peeling. Two required per car. Replaces Ford part # D1ZZ-6522244. Sold individually
Reproduction roofrail weatherstrip seal clip and quarter window guide clip for the 1971, 1972 and 1973 Mercury Cougar or Ford MustangFord Part #: D1ZZ-6522204
Sold individually. Zinc (dark silver)
Original Ford style fasteners used on most all Ford products starting in 1968. Sold in pairs. Zink (dark silver)
This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. You will notice the reproduction has a larger head (The two on the right in the lower picture are repros) than both of the used versions typically found on 67-73 Cougars. This will be a benefit to those that have elongated screw holes on your wheel lip mouldings from corrosion or improper removal. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding,...
Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD individually. See related items for kit of 10 screws. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970...
Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD AS A SET OF 10.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972...
Not 100% correct, but close and functional. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. Sold as a box of 100.
This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out our video below for more info on mirror installation: Still have riv-nut questions? Here are riv-nut answers! ...
Seven (7) of these acorn nuts are used to hold the trunk trim moulding on to the trunk. Replaces Ford Part # 377767 For more insight on this tricky trunk trim, check out our video below: ...
Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.
These barrel nuts or clips are exactly like the original ones inserted into the trunk for attaching 1967-68 "Mercury" script, and 1971-72 Mercury Cougar "Mercury" Hood scripts. The manufacturer indicates that these tubular nuts fit 1/8" holes. Pin size on those emblems are 3/32". These clips are also used to attach the 1967 quarter panel emblems. The install is basically the same as shown here: https://youtu.be/mcd788WUNns ...
Used grade A rocker panel clip for the 71 - 73 Mercury Cougar
These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. This listing is for a bag of 25 clips. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare....
These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. Sold Individually. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare. You'll also save...
Good used set with no broken studs or missing tension wires on the metal end clips.
This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969-1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall.
If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...