Window Regulators / Door Window Hardware

D1ZZ-223A58-A Lower door guide insert to prevent rattling of the window. Two of these inserts are inserted into the lower door guide after the door glass run is installed. Plastic piece that is subject to cracking. Two needed per door, item sold individually. Click on images to enlarge. ...

384356-S Bolt with captured washer. Mounts the two stops and is used to install the channel assembly. Five total bolts per door glass, 10 used per car. Very specific sized captured washer for distributing pressure on the glass. Click on images to enlarge. 1970 similar. ...

373460-S Factory original used bolt used to fasten the guide to the door (2), and to hold the adjustable stop. Sold individually.

New bolt for installing the door glass window run on any 1969-70 Mercury Cougar or Ford Mustang. This is the lower bolt that goes into the bottom of the door. 1/4-20 threads, hex head but a shallow hex head, Originally installed with a rubber seal, which is not included. 7/16" hex head, these had a Ford part number of 379513-S100. 2 needed per door, 4 per car, sold individually. Black silicone is a good substitute for the seal.

Used bolt for installing the door glass window run on any 1969-70 Mercury Cougar or Ford Mustang. This is the lower bolt that goes into the bottom of the door. 1/4-20 threads, hex head but a shallow hex head, Originally installed with a rubber seal, which is not included. 7/16" hex head, these had a Ford part number of 379513-S100. 2 needed per door, 4 per car, sold individually.

If you are converting your early 1970 Mercury Cougar or 1969 or early 1970 Cougar Coupe or Convertible from glue in glass to bolt in glass this is the hardware kit you will need. You can reuse your four C9ZB elevators that bolt to these brackets, the only difference between C9ZB and D0ZB is that the C9ZB is fastened by two bolts and the D0ZB has two studs and nuts. Keep in mind that 1969 window regulators will need slight modification to work with this 1970 hardware as the 1970 regulator does...

Special bolt with large square captured washer. This one is longer of the two that install in the vent window frame. This bolt has a 1/2" hex head with and has about 1-7/8" of threads with a dog point. See your shop manual for actual procedure. See also 378696-S for the vent window and front door channel set screws. Ford part number 378694-S. 

Special bolt with large square captured washer. This one is shorter of the two that install in the vent window frame. This bolt has a 1/2" hex head with and has about 7/8" of threads with a dog point. See your shop manual for actual procedure. See also 378696-S for the vent window and front door channel set screws. Ford part number 379384-S2. 

New single bolt for attaching door and quarter window regulators on any 1969-73 Mercury Cougar or Ford Mustang or Ford anything most likely. AMK part. Sold individually, Ford part number 57487-S.

Used single bolt for attaching door and quarter window regulators on any 1969-73 Mercury Cougar or Ford Mustang or Ford anything most likely. Sold individually, Ford part number 57487-S.

Grade A, Rear stop bracket for driver side door window. Stops the window in the up position. Application passenger side door glass 1969-70 Mercury Cougar and Ford Mustang including Mach 1. One per door. Plate and bolts, included. Felt and rubber dipped section will be in good but not great shape. The felt strip really takes a beating. Please see related listing for plate only or B grade bracket without hardware. Ford part # C9ZZ-65222A55-A. Do you have questions about Glue-In vs Bolt-In glass?...

Grade B used. Rear door window stop bracket. Stops the window in the up position. Application driver side door glass 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Plan on replacing the felt, the rubber dipped section will also probably be cracked. One per door. Plate and bolts not included. Please see related listing for plate only or complete stop bracket assembly. Ford part # C9ZZ-65222A55-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to...

Grade A, Rear stop bracket for passenger side door window. Stops the window in the up position. Application passenger side door glass 1969-70 Mercury Cougar and Ford Mustang including Mach 1. One per door. Plate and bolts, included. Felt and rubber dipped section will be in good but not great shape. The felt strip really takes a beating. Please see related listing for plate only or B grade bracket without hardware. Ford part # C9ZZ-65222A54-A. Do you have questions about Glue-In vs...

Rubber bumper that fits into the bracket in the bottom center of the door shell. Fits all 1967-68 Mercury Cougar and 1965-68 Ford Mustangs. This is the rubber bumper for the window rest when the door glass is at its lowest. Bracket is in bottom of the center of the door. Fits both right and left doors.Correct for 1967 - 1968 but will work in 1969 - 1970 with Bolt-in glass if you cut it down. Sold separately, two required per car. Replaces Ford part # C5ZZ-6521762-B Check out our...

This is the rubber that goes into the bracket of the bottom of the center of the door, for 1969 or early 1970 Mercury Cougar and Ford Mustang with glue-in door glass. This bumper will not work if your door glass is the 1970 bolt-in glass. We also sell the version for the 67-68 and late 1970 bolt in glass. Ford part # C9ZZ-6521762-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for...

This is the rubber that goes into the bracket of the bottom of the center of the door, for 1969-1970 Mercury Cougar and Ford Mustang glued-in door glass.  Note that this bumper is substantially shorter than the 70 bolt-in door glass version.  See D0ZZ-6521762-A for the 1970 bolt-in door glass version.  If you are swapping out a door on a 69 or a 70 don't forget that the door glass is different between the years and, if you have to swap out the glass, you will need...

This is a metal "C" channel that glues to the bottom center of the glued-in door glass on 1969 and early 1970 Mercury Cougar and Ford Mustangs. This channel, helps protect the glass when lowered to the rubber stop at the bottom of the door. Ford part # C9ZZ-214A16-A. *HINT* Use the same professional grade of glass adhesive that you use for bonding the door glass to the two glass mounting brackets. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In...

Protects door glass when attaching window channel. Replaces Ford part # C9ZZ-6523258. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Bolt in door glass bushing for most 1970 Ford cars with bolted in door windows. This is the white plastic version. Starting in mid-1970 this bushing was made out of black plastic. Except for color they are interchangeable. Ford part # D0ZZ-6523258-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Most often these do not wear out but instead get lost. These plastic bushings keep the threaded studs from the window elevators from touching the glass as they pass through the holes in your 1970 bolt in door glass. Eight required per car. Replaces Ford part # C9ZZ-6323266 or C9ZZ-6523258-B. *NOTE* These bushings also fit the door glass for the 1969 Mustang Fastback. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or...

Rear bracket for mounting in the 1970 door glass on the driver side door. 1970 Mercury Cougar and Ford Mustang with bolt in glass. Ford part # D0ZZ-6521431-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Rear bracket for mounting in the 1970 door glass on the passenger side door. 1970 Mercury Cougar and Ford Mustang with bolt in glass. Ford part # D0ZZ-6521430-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Front bracket for mounting in the 1970 door glass on the driver side door. 1970 Mercury Cougar and Ford Mustang with bolt in glass. Comes with stud that attaches to window regulator. We also have examples in which the stud is missing for a reduced price. We are looking to find someone to manufacture the T-studs. Both glue-in and bolt-in versions. Please let us know. Ford part # D0ZZ-6523288-B. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In...

Front bracket for mounting in the 1970 door glass on the passenger side (right hand) door. 1970 Mercury Cougar and Ford Mustang with bolt in glass. Comes with stud that attaches to window regulator. We also have examples in which the stud is missing for a reduced price. We are looking to find someone to manufacture the T-studs. Both glue-in and bolt-in versions. Please let us know. Ford part # D0ZZ-6523288-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly...

D1ZZ-6522380-B Used stabilizer that attaches to the top of the door in two different places. These have a fuzzy padded piece that keeps the glass from rattling while it goes up and down on the door run. In most cases, the padded fuzzy material is worn or missing. It appears that these could be repaired with fuzzy side of velcro.

Bracket or flat piece of channel for the sliding part of the window regulator Right and left interchange. One per door, screws are included. 1970 Mercury Cougar and Ford Mustang bolt in door glass. Attaches to the 1970 rear window bracket with nuts. Ford part # D0ZZ-6521504-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

C7ZZ-652221-B Restored, stainless steel "L" shaped top frame for 1967-68 Mercury Cougar and Ford Mustang Hardtops. Driver side only, there is a slight curvature which make these side specific. When these are taken apart, the rubber channel section falls apart during removal, keep this in mind. *Note - Excludes Mustang fastback and convertible.

C7ZZ-652221-B Stainless steel "L" shaped top frame for 1967-68 Mercury Cougar and Ford Mustang Hardtops. Driver side only, there is a slight curvature which make these side specific. When these are taken apart, the rubber channel section falls apart during removal, keep this in mind. *Note - Excludes Mustang fastback and convertible.

C7ZZ-652220-B Stainless steel "L" shaped top frame for 1967-68 Mercury Cougar and Ford Mustang Hardtops. Passenger side only, there is a slight curvature which make these side specific. When these are taken apart, the rubber channel section falls apart during removal, keep this in mind. *Note - Excludes Mustang fastback and convertible.

C7ZZ-6521459-B Bare channel for mounting the left side or driver door glass in a 1967-68 Mercury Cougar of Ford Mustang. We verify that the plastic rollers and plastic guide are in good, unbroken condition. Regulator slide not included, see related items for the slides. Those are in short supply. Can also be found with part number C7ZZ-6521459-C. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search...

C7ZZ-6521458-B Bare channel for mounting the right side or passenger door glass in a 1967-68 Mercury Cougar of Ford Mustang. We verify that the plastic rollers and plastic guide are in good, unbroken condition. Can also be found with part number C7ZZ-6521458-C. Regulator slide not included, see related items for the slides. Those are in short supply. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on...

Front bracket for mounting glued in door glass for all 1969 and very early 1970 Mercury Cougar and Ford Mustangs, passenger side front bracket only. Comes without stud that attaches to window regulator. We also have examples with the stud for a premium price. Here is the 3M product used to glue the glass to the bracket. We also have stud keepers available if you need to reattach your loose stud. Keeper also available for the T stud. We are looking to find someone to manufacture the...

Front bracket for mounting glued in door glass for all 1969 and very early 1970 Mercury Cougar and Ford Mustangs, passenger side front bracket only. Comes with stud that attaches to window regulator. We also have examples in which the stud is missing for a reduced price. Here is the 3M product used to glue the glass to the bracket. Keeper also available for the T stud. We are looking to find someone to manufacture the T-studs. Both glue-in and bolt-in versions. Please let us know. Ford...

Front bracket for mounting glued in door glass for all 1969 and very early 1970 Mercury Cougar and Ford Mustangs, passenger side front bracket only. Comes without stud that attaches to window regulator. We also have examples with the stud for a premium price. Here is the 3M product used to glue the glass to the bracket. Keeper also available for the T stud. We are looking to find someone to manufacture the T-studs. Both glue-in and bolt-in versions. Please let us know. Ford part #...

Front bracket for mounting glued in door glass for all 1969 and very early 1970 Mercury Cougar and Ford Mustangs, passenger side front bracket only. Comes with stud that attaches to window regulator. We also have examples in which the stud is missing for a reduced price. Here is the 3M product used to glue the glass to the bracket. Keeper also available for the T stud. We are looking to find someone to manufacture the T-studs. Both glue-in and bolt-in versions. Please let us know. Ford part #...

Rear bracket for mounting glued in door glass for all 1969 and very early 1970 Mercury Cougar and Ford Mustangs, driver side rear bracket only. Comes as shown, no cracks, distortions or stripped threads. Here is the 3M product used to glue the glass to the bracket. 1969 glass is glued in approximately 1 inch from the rear edge. 1970 glued in glass is approximately 2-1/4 inches from the straight edge if extended with an imaginary line from the rear edge of glass. Ford part # C9ZB-65223A19-A. "...

Rear bracket for mounting glued in door glass for all 1969 and very early 1970 Mercury Cougar and Ford Mustangs, passenger side rear bracket only. Comes as shown, no cracks, distortions or stripped threads. Here is the 3M product used to glue the glass to the bracket. 1969 glass is glued in approximately 1 inch from the rear edge. 1970 glued in glass is approximately 2-1/4 inches from the straight edge if extended with an imaginary line from the rear edge of glass. Ford part # C9ZB-65223A18-A....

C7ZZ-65222A57-C Bare guide without hardware for the driver side door glass of all 1967-68 Mercury Cougar and Ford Mustangs. Sometimes called the slider, mounts to the door. *Installation hint - all of the dried crusty 40+ year old grease should be removed and fresh white grease should lavishly be coated in the channel. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view...

C7ZZ-65222A56-C Bare guide without hardware for the passenger side door glass of all 1967-68 Mercury Cougar and Ford Mustangs. Sometimes called the slider, mounts to the door. *Installation hint - all of the dried crusty 40+ year old grease should be removed and fresh white grease should lavishly be coated in the channel. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to...

Window guide or 'elevator'. 1969 through early 1970 Mercury Cougar and Ford Mustang door glass. Two guides per door. Sold individually, will have undamaged excellent threads. Ford master part number C9ZZ-65222A56-A. *Note will not have original plastic bushing inserts installed. You will need to reuse your originals or purchase new or used. Please see related items. Ford part # C9ZB-65223A00-A. *NOTE* Excludes 1970 bolt in door glass. Do you have questions about Glue-In vs Bolt-In glass?...

Window guide or 'elevator'. 1970 Mercury Cougar and Ford Mustang door glass. Two guides per door. Sold individually. Ford master part number D0ZZ-65222A56-A. *Note will not have original plastic bushing inserts installed. Consider reproduction inserts, or plan on re-using your originals. 4 total inserts needed per window guide. Ford part # D0ZB-65223A00-A. *NOTE* This can also be used in conjunction with 69-70 (early) glue in glass. The 69 version is identical except for that 69 was...

C7ZZ-65222A57-KIT Guide with hardware for the driver side door glass of all 1967-68 Mercury Cougar and Ford Mustangs. Sometimes called the slider, mounts to the door. Kit includes guide, attaching bolts, detachable stop, and special set screw and nut for angle adjustment. *Installation hint - all of the dried crusty 40+ year old grease should be removed and fresh white grease should lavishly be coated in the channel. Check out our handy diagram below to find other '67-'68 door parts you may...

Reproduction door glass run. This is the metal tube that the windows go up and down on, sometimes called an elevator shaft. Left side door only. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Two per door. Front is same as rear. Check out our used door glass runs, original Ford and lower priced.NOTE: To get the orientation correct on these rods, lay the base of it flat on a table - the rod will lean toward the rear of the door. OK reproduction, but the...

This is one of the metal tubes that the windows go up and down on, sometimes called an elevator shaft. Left side door only. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Two per door. Front is same as rear. Sometimes marked with a letter "L", for left.NOTE: To get the orientation correct on these rods, lay the base of it flat on a table - the rod will lean toward the rear of the door. Ford part # C9ZZ-6521547-A. Do you have questions about Glue-In vs Bolt-In glass? How...

Reproduction door glass run. This is the metal tube that the windows go up and down on, sometimes called an elevator shaft. Right side door only. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Two per door. Front is same as rear. Check out our used door glass runs, original Ford and lower priced.NOTE: To get the orientation correct on these rods, lay the base of it flat on a table - the rod will lean toward the rear of the door. Ford part # C9ZZ-6521546-A. Do...

This is one of the metal tubes that the windows go up and down on, sometimes called an elevator shaft. Right side door only. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Two per door. Front is same as rear. Sometimes marked with a single "R", for right.NOTE: To get the orientation correct on these rods, lay the base of it flat on a table - the rod will lean toward the rear of the door. Ford part # C9ZZ-6521546-A. Do you have questions about Glue-In vs Bolt-In...

D1ZZ-6521546-B Used metal door run for all 1971-73 Mercury Cougar and Ford Mustangs. These years only used a single door run on each door. These are not side specific as in prior years. Fits either the passenger or driver side doors. During installation lube with white grease.

D1ZZ-6521790-A Lower window stop for the door glass on 1971-73 Mercury Cougar and Ford Mustang. Just one of these stops per door. These have one end coated with a rubberized plastic as a cushion.